Trhové ceny komoditných plastov týždenne
Uvádzame tu trhové ceny rôznych typov komoditných plastov PE-LD, PE-HD, PP a PS v strednej a východnej Európe s oneskorením 5 týždňov. Údaje spracoval náš partner myCEPPI.
Zaujímajú Vás aktuálne ceny komoditných plastov? Objednajte si túto službu Týždenné ceny komoditných plastov u nás v redakcií.
Ceny na týždeň 27/2017
Polyolefin price correction in July
The following factors influenced “commodity” polymer prices and price expectations last week:
- balanced supply,
- low demand,
- BRENT oil price 47.92 USD, tendency of dropping prices
- EUR getting stronger, EUR/USD exchange rate permanently close to 1.14
- Monomer (C2) and propylene monomer (C3) price reduction by 50 €.
In detail
The 50 € price drop surprised the market. Last week traders have already forecast a dynamic demand for July. They were of opinion that purchases would start as early as in July, as polymer prices have dropped to a level not seen for a long time. In advance market players calculated with a monomer price drop by 20-30 €, the reduction by 50 € is a surprise.
The price drop by 20-30 € happened as early as June both in case of PE and PP. The question is whether there is going to be another drop by 20 €. Our answer is: there will be some producers, who will do that, others won’t.
The monomer price drop by 50 € has also one absolute advantage. This allows producers with prices stuck on high level to bring them back to the level of competitors. In this way we can anticipate that on markets with high prices (e.g. in Hungary) there will be a major price correction, reduction both in case of PP and PE.
The extent of the styrene monomer price change was not known at the time when our report was written, it is also hard to forecast it, both minor decrease and slight increase are possible. The PS market is still balanced. This week the July price of SM came into the focus of interest.
Polyolefin grades
In case of LDPE the price ranges were unchanged, the market is already waiting for the price ranges to hit bottom. The lowest prices remained within the still very broad range of 1,130-1,220 €. The price range for medium-sized buyers is 1,230-1,270 €. Here there are also sufficient quantities of goods available. In case of the July prices a price drop by 20-30 € is anticipated. This can be different, depending on the buyer and producer concerned, the price drop by 50 € allows to pull the two extreme values of the price ranges together as we have indicated in our forecasts.
Low HDPE demand continued and it is not expected to increase in July either. On the average we anticipate a price decrease by 30-50 € and the two extreme values of the price range getting closer. It is possible that some prices of Serbian producers will be below 1,000 €.
The pipe market is dynamic, there is season for those products. We do not expect major price drop, prices will be reduced by an average 25-45 €.
LLDPE C4 supply is still low, but the product is absolutely following monomer prices, thus we anticipate a price drop by 40-60 €, the new price range will be 1,100-1,150 €. The reason is in particular that due to the € getting stronger an increasing quantity of imported goods arrives in Central-Europe as well.
PPH demand is consistent. The price range of simple grades is still 1,050-1,100 €. Unfortunately the monomer price reduction by 50 € at the southern producers of the region “pushes” prices below 1,000 €. Such a thing did not happen for a long time. In case of PPH the absolute necessity of a price correction exceeding monomer prices is palpable in case of many producers. In this way prices will get into balance slowly, by the middle of the month only.
In case of PPC we anticipate a price drop by 40-60 €. The latter will be the price correction of prices sticking on high price level. Large buyers can buy in a price range of 1,140-1,180, medium-sized ones in a range of 1,190-1,220 €. Because of the expected correction it will take time for prices to get balanced.
In case of PPR we anticipate no surprises, following monomer prices is the probable scenario. Depending on the grade, the new prices will be in a range of 1,150-1,270 €.
The prices of the last week and the producer price ranges expected for early July are presented in the table below (full truck load 20-22.5 t):
Grade name | Typical polymer price ranges in the last week of June, 2017, Central Europe (€/ton) | Expected polymer price ranges in the first week of July, 2017, Central Europe (€/ton) |
HDPE BM | 1,080-1,200 | 1,020-1,150 |
HDPE Film | 1,080-1,200 | 1,000-1,150 |
HDPE IM | 1,050-1,190 | 970-1,160 |
HDPE Pipe (100) | 1,270-1,350 | 1,225-1,300 |
LDPE Film | 1,130-1,270 | 1,100-1,210 |
LDPE GP | 1,130-1,270 | 1,100-1,210 |
LLDPE C4 | 1,150-1,200 | 1,100-1,150 |
PPC | 1,180-1,270 | 1,140-1,200 |
PPH IM | 1,060-1,200 | 990-1,150 |
PPH Raffia | 1,050-1,150 | 970-1,160 |
PPR | 1,200-1,310 | 1,160-1,250 |
GPPS | 1,250-1,320 | n/a |
HIPS | 1,390-1,480 | n/a |
EPS | 1,320-1,400 | n/a |
Polystyrene grades
The styrene monomer price is not yet known. Market players, buyers do not anticipate significant price changes in July. For the time being even the direction is a question mark, as the SM price underwent a downward correction, but PS prices from European source show an increase.
The main season for EPS will start in July, the ideal thing would be a slightly increasing SM price. In that case major disturbances on the market could be avoided. According to the opinion of market players an increase by 20-30 € would be ideal, and this price would also follow the increased demand for EPS. The ideal price range would be 1,340-1,420 €.
GPPS demand is good, supply is broad. There is a strong, increasing import supply from Iran, Saudi-Arabia, Egypt and Russia alike. This means that local producers have to get adapted to import prices that are getting cheaper and cheaper due to the strong €. The market is under pressure to reduce prices, but the price of SM will determine the direction. At any rate it is sure that in case of increasing SM it will be difficult to enforce price increase.
In case of HIPS demand is good and supply is stable. We experienced no change compared to last week. The price change of July will absolutely be following monomer prices.
Typ | Cena |
---|---|
HDPE blow molding | 1178 € / t |
HDPE film | 1171 € / t |
HDPE injection molding | 1157 € / t |
HDPE pipe (100) | 1313 € / t |
LDPE film | 1240 € / t |
LDPE general purpose | 1247 € / t |
PP co-polymer injection molding | 1241 € / t |
PP homo-polymer fiber | 1131 € / t |
PP homo-polymer injection molding | 1143 € / t |
PPR | 1272 € / t |
GPPS | 1315 € / t |
HIPS | 1400 € / t |
EPS | 1330 € / t |
myCEPPI - nový prístup v poradenstve a v spravodajstve v oblasti plastov. Poskytneme Vám detailný, aktuálny a na mieru vytvorený obraz o trhu s plastami v strednej a východnej Európe.
Vychádzame z našich osobných a pevných vzťahoch s významnými hráčmi v plastikárskom priemysle v strednej a východnej Európe. Každý mesiac uskutočňujeme stovky osobných a telefonických hovorov so spracovateľmi plastov, distribútormi a výrobcami surovín, zúčastňujeme sa odborných veľtrhov a konferencií.
Informácie, ktoré zhromažďujeme v rámci tohto procesu, tvoria základ našich týždenných cenových reportov komoditných plastov. Obsahujúce taktiež analýzu trhu. Tieto reporty taktiež slúžia ako východiskový bod pre naše ďalšie konzultačné služby ktoré poskytujeme spoločnostiam, ktoré potrebujú pomoc pri vstupe na trh, prípadne pri rozširovaní svojho biznisu, zorientovaní sa v situácií na trhu, atď. Naši odborníci majú desiatky rokov skúseností s plastami.
Radi Vám poskytneme naše služby.
História cien
- 2025:
- 2024:
- 2023:
- 2022:
- 2021:
- 2020:
- 2019:
- 2018:
- 2017:
Najnovšie inzeráty
Predám: Gumový granulát, gumové zmesi
27.01.2025 | ID: 202520364
-
27.01.2025 | ID: 202520363
Predám: PC vstrekovacia transparentná drť
27.01.2025 | ID: 202520361
-
27.01.2025 | ID: 202520360
Predám: Odprašovacie zariadenie ARV 38
27.01.2025 | ID: 202520359
-
27.01.2025 | ID: 202520358
-
27.01.2025 | ID: 202520357
-
27.01.2025 | ID: 202520356
Predám: HDPE regranulát - natur/biela
27.01.2025 | ID: 202520355
-
27.01.2025 | ID: 202520357
Kúpim: Nespracovaný materiál z výroby
27.01.2025 | ID: 202520350
-
24.01.2025 | ID: 202520347
Kúpim: Plastové odpady PE-PP fólie
22.01.2025 | ID: 202520341
Kúpim: ABS drť vstrekovacia biela
21.01.2025 | ID: 202520336
-
20.01.2025 | ID: 202520329
Kúpim: Nespracovaný materiál z výroby
20.01.2025 | ID: 202520328
-
20.01.2025 | ID: 202520321
-
14.01.2025 | ID: 202520302
Predám: Gumový granulát, gumové zmesi
27.01.2025 | ID: 202520364
-
27.01.2025 | ID: 202520363
Predám: PC vstrekovacia transparentná drť
27.01.2025 | ID: 202520361
-
27.01.2025 | ID: 202520360
Predám: Odprašovacie zariadenie ARV 38
27.01.2025 | ID: 202520359
-
27.01.2025 | ID: 202520358
-
27.01.2025 | ID: 202520356
Predám: HDPE regranulát - natur/biela
27.01.2025 | ID: 202520355
Predám: HDPE regranulát - natur
27.01.2025 | ID: 202520354
Najbližšie výstavy
04.02.2025 - 06.02.2025 | Anaheim
04.02.2025 - 06.02.2025 | Varšava
11.02.2025 - 13.02.2025 | Monterrey
International Plastic Industry IPF 2025
12.02.2025 - 15.05.2025 | Dhaka
12.02.2025 - 13.02.2025 | Birmingham
18.02.2025 - 19.02.2025 | Nuremberg
19.02.2025 - 20.02.2025 | Amsterdam
23.02.2025 - 25.02.2025 | Shanghai
24.02.2025 - 26.02.2025 | Alžír
04.02.2025
04.02.2025
11.02.2025
International Plastic Industry IPF 2025
12.02.2025
12.02.2025
SOPK Vás pozýva na Konferenciu Očakávaný vývoj slovenskej ekonomiky v roku 2025
28.01.2025
Rozlúčte sa s povrchovými defektami výrobkov pomocou pokročilého chladenia
05.02.2025
18.02.2025
Vzdelávací program ING 4.0 pre rozvoj digitálnych zručností: Zber dát, ich analýza a strojové učenie
20.02.2025
Vzdelávací program ING 4.0 pre rozvoj digitálnych zručností: Inteligentná údržba
20.02.2025
Ponuky práce
Obchodník v oblasti recyklácie plastov (regranulácie) - DALGA GROUP s.r.o.
23.01.2025
Formár/Nástrojár - ULSTRUP PLAST s.r.o.
23.01.2025
Operátor výroby - DALGA GROUP s.r.o.
17.01.2025
Obchodný zástupca granuláty - ALBIS PLASTIC CR s.r.o.
16.01.2025
Obchodný zástupca pre recykláciu - SILON CZ Recycling s.r.o.
14.01.2025
Obchodný manažér - FORM s.r.o.
13.01.2025
Obchodný zástupca granuláty, pre ALBIS PLASTIC CR s.r.o.
07.01.2025
-
18.12.2024
Pracovník v sklade - prax na VZV nutná. ENVI-RECYCLING PLAST, s. r. o.
09.12.2024